Patton-electronic 3088 Manual de usuario

USER MANUAL MODEL 3088 RocketLink-G NTU G.SHDSL Modem SALES OFFICE(301) 975-1000TECHNICAL SUPPORT(301) 975-1007 Part# 07M3088-UMDoc# 03325U2-001 Rev

10 Clock ModeControls DSL and serial clock sources. Internal clock mode means the 3088 provides its own clock to both the serial interface and the DS

11 4.1 CONFIGURING THE DIP SWITCHES The Model 3088 is equipped with two sets of DIP switches, which allow con-figuration of the unit for a wide varie

12 The two sets of DIP switches on the underside of the Model 3088 are referred to as S1 and S2 . As shown in figure 3, the orientation of all DIP

13 Configuration Reset to Factory Defaults To recover from a forgotten password, the user may reset the unit to its factory configuration. After seeing

14 S1-8: TX ClockS1-7 – S1-1: Data Rate This setting controls the DSL data rate and the serial data rate. S1-8 Setting Description ON Normal TD sampl

15 ON ON OFF OFF OFF OFF ON 1920ON ON OFF OFF OFF OFF OFF 1984ON OFF ON ON ON ON ON 2048ON OFF ON ON ON ON OFF 2112ON OFF ON ON ON OFF ON 2176ON OFF

16 Loops The V.35 interface has pins two pins, one to request an LAL and the other to request and RDL. If DTE loops are enabled, then when these pins

17 S2-3: Annex A/B Annex A is typically used in North American-like networks, whereas Annex B is typically used in European-like networks. The differ

18 • Circuit ID : The circuit ID communicated to other units via EOC. EOC (Embedded Operations Channel) is an out-of-band channel specified in the G

19 • FPSW Settings : What the front panel switches are set to (if the unit is populated with them).• Configuration Mode : Whether the 3088 is configure

2 CONTENTS1.0 Compliance Information... 4 1.1 Radio and TV Interference...

20 Help Commands The following commands are provided to help the user find the correct command:• help: Lists all the commands that the console recogn

21 • system set clockmode <internal|external|receiverecover>: Sets the clock mode. Internal clock mode means the 3088 provides the clock to bo

22• system show leds: Shows the current state of all software controlled LEDs.• system show fpsw: Shows the current front panel switch settings.DSL Co

23• dsl set errmon startdelay <startdelay>: Sets the number of seconds to wait after the DSL link comes up before the error monitor starts inspe

24• dsl show syncstate: Shows the sync state of the DSL link: out of sync, acquiring sync, in sync, or losing sync• dsl show linkspeed: Shows the actu

25The dsl clear errcntrs command clears the error counters.Remote ConsoleProvided that there is a DSL link to a second 3088, a user may login to the fi

26password: ******> dsl clear errcntrs> dsl show errcntrscrc: 0losw: 0tx fifo full: 0tx fifo empty: 0tx fifo slip: 0tx stuf

27Follow the instructions below to activate RocketLink Plug ‘n’ Play between CO (Model 3096RC and CP (Model 3088) units:• Set the Model 3096RC (CO) to

285.0 INSTALLATIONOnce the Model 3088 is properly configured, it is ready to connect to the twisted pair interface, to the serial port, and to the pow

29The RJ-45 connector on the Model 3088’s twisted pair interface is polar-ity insensitive and is wired for a two-wire interface. The signal/pin rela-t

3 6.0 Operation... 33 6.1 Power-up ...

30Connecting the Model 3088/CA (V.35) to a “DCE” DeviceThe Model 3088/CA provides a V.35 DCE (data circuit terminating equip-ment) interface on an DB-

31ment) for connection to DCE such as a modem or multiplexer. When connecting the X.21 interface of the Model 3088/D to your DTE or DCE device, use an

32The DCE/DTE strap is located on the top side of the 3088/D pc board (See figure 10, below). The arrows on the top of the strap indicate the configurat

336.0 OPERATIONOnce the Model 3088 is properly configured and installed, it should oper-ate transparently. This sections describes power-up, reading t

34Term (Green)The Term LED glows solid under the following circumstances:• 3088/CA with V.35 interface: If the serial interface has asserted DTR• 3088

35.Figure 13. Local Analog Loopback diagramThe data received from the serial interface is looped back before going out on the DSL line. Note that this

367.0 REMOTE CONSOLE MANUAL INFORMATIONThe PC user (near-end) may configure and verify status of the remote 3088 (far-end) via a Remote Console sessio

37— If 3088 (Far End) already has an active remote console session open, you will see the message Console: Remote console con-nection request rejected

38Figure 16 is a screenshot of opening a typical remote console session:Figure 16. Opening a typical remote console sessionHow to DisconnectThe remote

39lowing is what is displayed upon a user’s logging out of a remote console session after logging in.> remote console>Console: Remote console co

4 1.0 COMPLIANCE INFORMATION1.1 RADIO AND TV INTERFERENCE The equipment generates and uses radio frequency energy, and if not installed and used pr

403088 (near-end). However the local 3088 (near-end) is unable to receive this message and the local 3088 (near-end) does not know to terminate the R

418.0 MODEL 3088 SOFTWARE UPGRADE FEATUREThe 3088 is software upgradeable through the console port. Software images will be available in Intel Hex fil

429.0 RESET CONFIGURATION TO FACTORY DEFAULTSThe configuration can be reset to factory defaults from the software reset mode. This allows a user to re

43APPENDIX ASPECIFICATIONSA.1 CLOCKING MODESInternal, external (V.35 only), or receive recoveredA.2 DTE RATEAll 64k steps from 64 to 4608 kbpsA.3 S

44Term (Green)The Term LED glows solid under the following circumstances:• 3088/CA with V.35 interface: If the serial interface has asserted DTR• 3088

45A.13 LINE INTERFACETransformer coupled, 2500 VRMS isolationA.14 G.SHDSL PHYSICAL CONNECTIONRJ-45, 2-wire polarity insensitive pins 4 and 5A.15 EN

46APPENDIX BFACTORY REPLACEMENT PARTS AND ACCESSORIESModel # Description08055DCUI 100–240VAC (+5V ±5% reg. DC/2A) Universal Input Adapter0805EUR Euro

47APPENDIX CMODEL 1088/CA INTERFACE PIN ASSIGNMENTSV.35 INTERFACEDB-25 FEMALE CONNECTOR(DCE ORIENTATION)Pin # Signal1 Frame Ground2 TxD-a3 RxD-a4RTS5

48APPENDIX DMODEL 3088/D INTERFACE PIN ASSIGNMENTSX.21 INTERFACED-SUB-15 FEMALE CONNECTORDTW/DCE ORIENTATIONCopyright © 2005Patton Electronics Company

5 the telephone network, the telephone company may request that you dis-connect the equipment until the problem is resolved.Connection to party line

6 2.0 WARRANTY INFORMATION Patton Electronics warrants all Model 3088 components to be free from defects, and will—at our option—repair or replace t

7 3.0 GENERAL INFORMATION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and

8 4.0 CONFIGURATION The Model 3088 (see figure 1) has two configuration modes, DIP switch and software. Figure 1. Model 3088 (3088/D version shown) D

9 The Model 3088 provides the following parameters for configuring the unit. Parameter DescriptionPossible ValuesDefault Value Password The password u